Duplex 2507 (UNS S32750)

Duplex 2507 (UNS S32750) is a super duplex stainless steel with 25% chromium, 4% molybdenum, and 7% nickel designed for demanding applications which require exceptional strength and corrosion resistance, such as chemical process, petrochemical, and seawater equipment.

Duplex Stainless Steels, also referred to as austeniticferritic stainless steels, are a family of grades having around equal proportions of austenite and ferrite.

These steels have a duplex microstructure which contributes to their high strength and high resistance to stress corrosion cracking.

Duplex steels offer high resistance to uniform and local corrosion because of their high content of nitrogen, chromium and molybdenum. Duplex stainless steels have good weldability.

There are three groups of duplex stainless steels that include the following:

Standards

S32750 or Duplex 2507

Duplex 2507 is a super duplex stainless steel developed for applications that demand high strength and corrosion resistance. Alloy 2507 has 25% chromium, 4% molybdenum, and 7% nickel.

This high molybdenum, chromium and nitrogen content causes high resistance to chloride pitting and crevice corrosion attack and the duplex structure provides 2507 with exceptional resistance to chloride stress corrosion cracking.

Using Duplex 2507 must be restricted to applications below 600° F (316° C). Extended elevated temperature exposure can reduce both the toughness and corrosion resistance of alloy 2507.

Duplex 2507 has good mechanical properties. Often a light gauge of 2507 material can be used to achieve the same design strength of a thicker nickel alloy. The resulting weight savings can considerably reduce the overall cost of fabrication.

Properties of Super Duplex Steel 2507 or S32750

Applications of S32750 Super Duplex Stainless Steel

Alloy 2507 (UNS S32750) is a super duplex stainless steel with 25% chromium, 4% molybdenum, and 7% nickel designed for demanding applications which require exceptional strength and corrosion resistance, such as chemical process, petrochemical, and seawater equipment. The steel has excellent resistance to chloride stress corrosion cracking, high thermal conductivity, and a low coefficient of thermal expansion. The high chromium, molybdenum, and nitrogen levels provide excellent resistance to pitting, crevice, and general corrosion.

The applications of S32750 super duplex stainless steel are:

Chemical Analysis

Typical Values (Weight %)

Carbon Chromium Nickel Molybdenum Nitrogen Others
0.020 25 7 4.0 0.27 S=0.001
PREN = [Cr%] = 3.3 [Mo%] = 16 [N %] ≥ 40
Mechanical Properties

Mechanical and Physical Properties

2507 combines high tensile and impact strength with a low coefficient of thermal expansion and high thermal conductivity. These properties are suitable for many structural and mechanical components. The low, ambient, and elevated temperature mechanical properties of 2507 sheet and plate are shown below. All of the test data shown are for samples in the annealed and quenched condition.

2507 is not recommended for applications which require long exposures to temperatures in excess of 570°F because of the increased risk of a reduction in toughness. The data listed here are typical for wrought products and should not be regarded as a maximum or minimum value unless specifically stated.

Properties

0.2% Offset Yield Strength, ksi

Ultimate Tensile Strength, ksi

1% Offset Yield Strength, ksi

Elongation in 2 inches, %

Hardness, Rockwell C

影响能源、英尺-磅

80 min.

116 min.

91 min.

15 min.

32 max

74 min.

Low Temperature Impact Properties

Temperature °F RT 32 -4 -40
Ft-lbs 162 162 155 140
Temperature °F -76 -112 -148 -320
Ft-lbs 110 44 30 7

Elevated Temperature Tensile Properties

Temperature °F 68 212 302 392 482
0.2% Offset Yield Strength, ksi 80 65 61 58 55
Ultimate Tensile Strength, ksi 116 101 98 95 94

Values obtained for hot rolled plates (th ≤ 2"). Alloy 2304 must not be used for a long time at temperatures higher than 300°C (572°F), where precipitation hardening phenomenon occurs.

Physical Properties

Density : 7,800 kg/m3 - 0.28 lb/in3

Interval
Temper
°C
Thermal
expansion
ax10M-bK-1
°C

再保险sistivity

(μ_ cm)
Thermal
conductivity
(W.m-1.K-1)
Specific
heat
(J.kg-1.K-1
Young
modulus
E
(GPa)
剪切
modulus
G
(GPa)
20-100 13 20 80 17 450 200 75
20-100 13 100 92 18 500 190 73
20-200 13.5 200 100 19 530 180 70
20-300 14 300 105 20 560 170 67
Processing

Hot Forming

2507 should be hot worked between 1875 F and 2250 F. This should be followed by a solution anneal at 1925F minimum and a rapid air or water quench.

Cold Forming

Most of the common stainless steel forming methods can be used for cold working 2507. The alloy has a higher yield strength and lower ductility than the austenitic steels so fabricators may find that higher forming forces, increased radius of bending, and increased allowance for springback are necessary. Deep drawing, stretch forming, and similar processes are more difficult to perform on 2507 than on an austenitic stainless steel. When forming requires more than 10% cold deformation, a solution anneal and quench are recommended.

Heat Treatment

2507 should be solution annealed and quenched after either hot or cold forming. Solution annealing should be done at a minimum of 1925 F. Annealing should be followed immediately by a rapid air or water quench. To obtain maximum corrosion resistance, heat treated products should be pickled and rinsed.